this manual may be trademarks or registered trademarks of their respective companies and are. View and Download Symbol LS quick start manual online. LS Scanner pdf manual download. Also for: Ds View and Download Motorola LSFZ product reference manual online . User Manual. LSFZ Barcode Reader pdf manual download.

Author: Brasho Daisho
Country: Tanzania
Language: English (Spanish)
Genre: Politics
Published (Last): 5 October 2010
Pages: 371
PDF File Size: 19.4 Mb
ePub File Size: 8.19 Mb
ISBN: 164-6-46026-323-7
Downloads: 67500
Price: Free* [*Free Regsitration Required]
Uploader: Arar

Motorola LS3408-FZ20005 Product Reference Manual

Synapse Interface Motorola recommends the default setting. This ensures compatibility between bar coded data and the host application; the scanner is programmed rather than modifying the host software. Software type and version number Motorola responds to calls by e-mail, telephone or fax within the time limits set forth in service agreements. To enable or disable EAN-8, scan the appropriate bar code below.


Reader has validated and stripped check digit. The following codes must be read three times: Symbologies manuxl – 29 Code 11 Check Digit Verification This feature allows the scanner to check the integrity of all Code 11 symbols to verify that the data complies with the specified check digit algorithm. Don’t show me this message again.

Programming Reference Symbol Code Identifiers This specular reflection can make decoding difficult. Redundancy Level 3, Redundancy Level 4 Symbologies 12 – 47 Redundancy Level 3 Code types other than the following maunal be successfully read twice before being decoded. Don’t have an account?

Selecting the host type sets the parameter defaults as listed in Table Reader has checked one check character. Light from a laser is all the same frequency, unlike the output of an incandescent bulb. Maanual Code 39 must be enabled in order for this parameter to function.


Characters to send all bar code data except for unknown characters. Medium Volume High Volume Power Mode This parameter determines whether or not the scanner enters reduced power mode after a decode attempt.

This may present a problem for customers with older systems that do not recognize some newer symbologies for example, RSS. Page Programming Reference B – 3 The modifier character is the sum of the applicable mankal values based on Ps3408 B In order to accomplish this, the I 2 of 5 code must be enabled, and the code must have a leading zero and a valid EAN check digit.

Page Glossary – 3 Continuous Code. NOTE Due to the construction of the D 2 of 5 symbology, it is possible for a scan line covering only a portion of the code to transmit as a complete scan, yielding less data than is encoded in the bar code. Page of Go. To program each data formatting rule: Symbologies 12 – 23 Code 39 Check Digit Verification When this feature is enabled, the scanner checks the integrity of all Code 39 symbols to verify that the data complies with specified check digit manuwl.

Symbol LS 3408 Quick Start Manual

Connect the other end of the Scanner Emulation interface cable to the scanner port on the mobile computer or controller. To implement this, first enter an ADF rule that applies to the normal situation.

Enabling this strips the leading ” from bar codes beginning with two or more zeros but not six zeros, and reports the bar code as UPC-A. Stop Bit Ls408 The stop bit s at the end of each transmitted character marks the end of transmission of one character and prepares manial receiving device for the next character in the serial data stream.

Enter a leading zero ls348 single digit numbers. Revision History Changes to the original manual are listed below: Then select one of four options: In case of an error, or to change the selection, scan Cancel page D For example, to decode only I 2 of 5 symbols with 14 characters, scan I 2 of 5 – One Discrete Length, then scan 1 followed by 4.


In addition to these bar codes for data formatting, see each host chapter for the appropriate host connections and host device features for the scanner. If the scanner was damaged in transit, contact Motorola Enterprise Mobility Support at one of the telephone numbers listed on page xv.

Parameter Pass-through Motorola compliant decoders can control the behavior of the entire system by scanning the necessary parameters only once.

If pad le3408 to length 6, send next 3 characters, stop padding, send next 5 characters is programmed, three zeros are added to the first send, and the next send is unaffected by the padding.

Use this mode when you need Scanner Emulation communication. No check digit processing. Discrete 2 Of 5 d mankal Of 5 Codes. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola.

Scan the appropriate bar codes to enable or disable each variant of GS1 DataBar. Rule Belongs To Set Three options are given for transmitting UPC-A preamble to the host device: No check digit is sent. The unique account number associated with a cellular device. Glossary – 7 SPP. Connect the modular connector of the Scanner Emulation interface cable to manhal cable interface port on the scanner. An MSI bar codewith a single check digit checked, is transmitted as